Lindy 39405 Manual do Utilizador

© LINDY ELECTRONICS LIMITED & LINDY-ELEKTRONIK GMBH - FIRST EDITION (April 2005) CPU IP Access Switch Lite User Manual English

2.2.3 Network Connection The IP ACCESS SWITCH LITE provides an RJ-45 port for an Ethernet connection. The port can be used with a 100Mbps, 100Base-T

3. Configuration The CPU IP ACCESS SWITCH LITE’s communication interfaces are all based on TCP/IP. The switch comes pre-configured with the IP confi

3.3 IP ACCESS SWITCH LITE Setup Tool 3.3.1 MAC Address Detection Connect the IP ACCESS SWITCH LITE to your computer either via a local network, or

3.3.2 Authentication To adjust the authentication settings, enter your login as a super user and change your password. Super user login Enter the

3.4 Keyboard, Mouse and Video configuration Between the IP ACCESS SWITCH LITE and the host, there are two interfaces available for transmitting keyb

3.4.3 Host System Mouse Settings The host's operating system obtains various settings from the mouse driver. Note: The following limitations

3.4.5 Recommended Mouse Settings For the different operating systems we can give the following advice... MS Windows 2000/2003 (Professional and Ser

4. Usage 4.1 Prerequisites The IP ACCESS SWITCH LITE features an embedded operating system offering a variety of standardized interfaces. This sect

4.2 Logging In 4.2.1 Login to the IP ACCESS SWITCH LITE Launch your web browser. Direct it to the address of your IP ACCESS SWITCH LITE which you

4.3 Navigation Once logged into the IP ACCESS SWITCH LITE successfully, the main page appears. This page consists of three parts; each of them conta

The Remote Console is the redirected screen, keyboard and mouse of the remote host system that the IP ACCESS SWITCH LITE switch controls. Selecting

Note: Your local keyboard changes its keyboard layout according to the remote host system. If you use a German administration system and your host sy

Options Opens the Options menu. A short description of the each of the options follows: Monitor Only Toggles the ‘Monitor Only’ filter on or off. I

Video Settings through the remote console: Brightness Controls the brightness of the picture Contrast Controls the contrast of

Soft Keyboard Opens up the sub-menu for the Soft-Keyboard: Show Pops up the Soft-Keyboard. The Soft-Keyboard is necessary in case your host system

4.3.3 Remote Console Status Line Status line Shows both console and the connection state. The size of the remote screen is displayed. The example be

5. Menu Options 5.1 Remote Control 5.1.1 KVM Console To open the KVM console, click either the menu entry on the left or on the console picture

5.1.2 Telnet Console The IP ACCESS SWITCH LITE firmware features a Telnet server that enables a user to connect via a standard Telnet client. If t

The following list shows the command mode syntax and their usage. Help Displays the list of possible commands Cls Clears the screen Quit Exits the

5.2 Virtual Media 5.2.1 Floppy Disk Follow the steps below to upload a virtual floppy image to the IP ACCESS SWITCH LITE and create a virtual flo

Contents 1. INTRODUCTION ...1 1.1 F

Windows Windows users should use the tool RawWrite for Windows which is included on the supplied CD. Launch RawWrite, you will see the window oppo

5.2.2 Create a CD-ROM/ISO Image Follow the procedure below to create a CD-ROM image which can be accessed by the host system via the IP ACCESS SWI

Windows To create the image file, use your favourite CD imaging tool. Copy the whole contents of the disc into one single image file on your hard dis

7. You will see the dialog below detailing the active image: 8. Click Reactivate. Access the console window and you will see that another CD dr

5.2.3 Drive Redirection The Drive Redirection feature allows the host system to access the CD-Rom drives, hard drives, floppy drives etc. on your

3. Follow the on-screen instructions. You will be asked to input your user name (default is super) and password (default is pass). 4. Continue

5. Choose the drive you wish to redirect from the drop-down list. Enter your user name and password and click OK. Warning: Please be aware t

5.3 User Management 5.3.1 Change Password To change your password, enter the new password in the upper entry field. Retype the password in the lowe

5.3.2 Users And Groups The IP ACCESS SWITCH LITE comes with 2 pre-configured user accounts that have fixed permissions. The super account has all p

5.4 KVM Settings 5.4.1 User Console The following settings are user specific. This means the super user can customize these settings for individual

4.3 Navigation... 15 4.3.1 Re

are very time consuming, they should not be used when several users are accessing the IP ACCESS SWITCH LITE simultaneously. The standard colour dept

Miscellaneous Remote Console Settings Start in Monitor Mode Sets the initial value for the monitor mode. By default the monitor mode is off. In cas

5.4.2 Keyboard/Mouse Host Interface Enables the interface the mouse is connected to. You can choose between Auto for automatic detection, USB for

Mouse Speed  Auto mouse speed Use this option if the mouse settings on the host use an additional acceleration setting. The IP ACCESS SWITCH LITE

5.5 Device Settings 5.5.1 Network The Network Settings panel allows network related parameters to be changed. Each parameter will be explained bel

Primary DNS Server IP Address IP address of the primary Domain Name Server in dot notation. This option may be left empty; however, the IP ACCESS SWI

5.5.2 Dynamic DNS A freely available Dynamic DNS service (dyndns.org) can be used in the following scenario (see illustration below) The IP ACCESS

Enable Dynamic DNS Enables the Dynamic DNS service. This requires a configured DNS server IP address. Dynamic DNS server This is the server name w

5.5.3 Security Force HTTPS If this option is enabled, access to the web front-end is only possible using an HTTPS connection. The IP ACCESS SWITCH

5.5.4 Certificate The IP ACCESS SWITCH LITE uses the Secure Socket Layer (SSL) protocol for any encrypted network traffic between itself and a conn

1. Introduction Thank you for purchasing the LINDY CPU IP ACCESS SWITCH LITE. This device allows operators to monitor and access their computers fro

After completing these three steps, the IP ACCESS SWITCH LITE has its own certificate that is used to identify it to its clients. Common name Note:

Confirm Challenge Password Confirmation of the Challenge Password Email The email address of a contact person that is responsible for the IP ACCESS

5.5.5 Serial Port The IP ACCESS SWITCH LITE Serial Settings allow you to specify what device is connected to the serial port and how to use it. Co

 Modem Init String The initialization string used by the IP ACCESS SWITCH LITE to initialize the modem. The default value will work with all moder

5.5.6 Date And Time Here you can set the internal real-time clock of the IP ACCESS SWITCH LITE. You can adjust the clock manually or use an NTP time

5.5.7 Event Log Important events like a login failure or a firmware update are logged to a selection of logging destinations. Each of those events

SMTP Logging enabled With this option, the IP ACCESS SWITCH LITE is able to send Emails to an address given by the Email address text field in the Ev

5.6 Maintenance 5.6.1 Device Information This section contains a summary with various information about the IP ACCESS SWITCH LITE and its current

5.6.2 Event Log Displays the log list including the events that are logged by the IP ACCESS SWITCH LITE. 5.6.3 Update Firmwa

A new firmware update is a binary file which can be sent to you by email or which you can download from our website www.lindy.com. Updating the fir

1.1 Features  Remote access of KVM switches or servers via LAN, WAN, or the internet; control your installation from almost anywhere in the world

5.6.4 Unit Reset This section allows you to reset specific parts of the device. This involves the keyboard and mouse, the video engine and the IP AC

57 6. Troubleshooting Q 001: The remote mouse doesn’t work or is not synchronized A 001: Make sure the mouse settings in IP ACCESS SWITCH LITE matc

58 Q 009: Using MacOS X an HTTPS connection fails A 009: You have to install the IP ACCESS SWITCH LITE certificate using our certificate installer,

59 7. Key Codes This table shows the key codes used to defines keystrokes or hotkeys for several functions. Please note that these key codes do not

60 The layout for this keyboard is also shown. However, most modifier keys and other alphanumeric keys used for hotkey purposes in application progra

61 8. Video Modes The table below lists the video modes that the IP ACCESS SWITCH LITE supports. Please do not use any other custom video settings;

62 9. Rack Mount Kit Installation

63 10. Radio Frequency Energy, Certifications CE Conformity This equipment has been tested and found to comply with the relevant European Community

1.3 Technical Specifications Item Description PC Port Connectors PS/2 Keyboard Mini Din 6 Pin Female PS/2 Mouse Mini Din 6 Pin Female VGA HDDB 15 P

2. Hardware Installation 2.1 Operation Overview The pictures below show the connection options of the IP ACCESS SWITCH LITE. The IP ACCESS SWITCH

2.2 Connections 2.2.1 Host Connection Side Use the supplied 3-in-1 combined KVM cable and USB cable to make the connections to the host computer. T